Mitsubishi FR-A820-3.7K-1 General-Purpose Inverter FREQROL-A800
Product Description:
Motor Specifications
The motor capacity requirement for this particular application is
3.7 kW. The input voltage class is specified as three-phase 200 V.
The output specification is three-phase with a capacity of 6.7 kVA.
The dimensions of the motor are as follows: height of 260 mm, width
of 150 mm, and depth of 140 mm. The motor also comes with a
protective structure.
The output rated current is 17.5 A and the output rated power
supply is three-phase 200-240 V.
Rated (Standard Structure Models) 200 V Class:
| Type Name FR-A820-[](-E)(GF) | 0.4 K | 0.75 K | 1.5 K | 2.2 K | 3.7 K | 18.5 K | 37 K | 45 K | 55 K | 75 K | 90 K |
|---|
| 00046 | 00077 | 00105 | 00167 | 00250 | 00930 | 01870 | 02330 | 03160 | 03800 | 04750 |
|---|
Applicable Motor Capacity
(kW) ∗1 | SLD | 0.75 | 1.5 | 2.2 | 3.7 | 5.5 | 22 | 45 | 55 | 75 | 90/110 | 132 |
|---|
| LD | 0.75 | 1.5 | 2.2 | 3.7 | 5.5 | 22 | 45 | 55 | 75 | 90 | 110 |
|---|
| ND (Initial Setting) | 0.4 | 0.75 | 1.5 | 2.2 | 3.7 | 18.5 | 37 | 45 | 55 | 75 | 90 |
|---|
| HD | 0.2∗2 | 0.4 | 0.75 | 1.5 | 2.2 | 15 | 30 | 37 | 45 | 55 | 75 |
|---|
| Output | Rated Capacity
(kVA) ∗3 | SLD | 1.8 | 2.9 | 4 | 6.4 | 10 | 35 | 71 | 89 | 120 | 145 | 181 |
|---|
| LD | 1.6 | 2.7 | 3.7 | 5.8 | 8.8 | 32 | 65 | 81 | 110 | 132 | 165 |
|---|
| ND (Initial Setting) | 1.1 | 1.9 | 3 | 4.2 | 6.7 | 29 | 55 | 67 | 82 | 110 | 132 |
|---|
| HD | 0.6 | 1.1 | 1.9 | 3 | 4.2 | 23 | 44 | 55 | 67 | 82 | 110 |
|---|
Rated Current
(A) | SLD | 4.6 | 7.7 | 10.5 | 16.7 | 25 | 93 | 187 | 233 | 316 | 380 | 475 |
|---|
| LD | 4.2 | 7 | 9.6 | 15.2 | 23 | 85 | 170 | 212 | 288 | 346 | 432 |
|---|
| ND (Initial Setting) | 3 | 5 | 8 | 11 | 17.5 | 76 | 145 | 175 | 215 | 288 | 346 |
|---|
| HD | 1.5 | 3 | 5 | 8 | 11 | 61 | 115 | 145 | 175 | 215 | 288 |
|---|
Overload Current
Rating ∗4 | SLD | 110% for 60 sec, 120% for 3 sec (inverse time characteristics),
ambient temperature 40°C |
|---|
| LD | 120% for 60 sec, 150% for 3 sec (inverse time characteristics),
ambient temperature 50°C |
|---|
| ND (Initial Setting) | 150% for 60 sec, 200% for 3 sec (inverse time characteristics),
ambient temperature 50°C |
|---|
| HD | 200% for 60 sec, 250% for 3 sec (inverse time characteristics),
ambient temperature 50°C |
|---|
| Rated Voltage∗5 | 3-phase 200 to 240 V |
|---|
| Regenerative Braking | Brake Transistor | Built-in | FR-BU2 (Option) |
|---|
| Maximum Brake Torque ∗7 | 150% Torque, 3% ED ∗6 | 100% Torque / 3% ED ∗6 | 20% Torque / Continuous | 10% Torque / Continuous |
|---|
| FR-ABR
(With Option Selected) | 150% Torque, 10% ED | 100% Torque / 10% ED | 100% Torque
/ 6% ED | - | - | - | - | - |
|---|
| Power Supply | Rated Input
AC Voltage / Frequency | 3-phase 200 to 240 V, 50 Hz / 60 Hz |
|---|
| Allowable AC Voltage Variation | 170 to 264 V, 50 Hz / 60 Hz |
|---|
| Allowable Frequency Variation | ±5% |
|---|
Rated Input
Current (A)
∗8 | Without DC Reactor | SLD | 5.3 | 8.9 | 13.2 | 19.7 | 31.3 | 115 | 221 | 269 | - | - | - |
|---|
| LD | 5 | 8.3 | 12.2 | 18.3 | 28.5 | 106 | 207 | 255 | - | - | - |
|---|
| ND (Initial Setting) | 3.9 | 6.3 | 10.6 | 14.1 | 22.6 | 96.3 | 181 | 216 | 266 | - | - |
|---|
| HD | 2.3 | 3.9 | 6.3 | 10.6 | 14.1 | 80 | 150 | 181 | 216 | - | - |
|---|
| With DC Reactor | SLD | 4.6 | 7.7 | 10.5 | 16.7 | 25 | 93 | 187 | 233 | 316 | 380 | 475 |
|---|
| LD | 4.2 | 7 | 9.6 | 15.2 | 23 | 85 | 170 | 212 | 288 | 346 | 432 |
|---|
| ND (Initial Setting) | 3 | 5 | 8 | 11 | 17.5 | 76 | 145 | 175 | 215 | 288 | 346 |
|---|
| HD | 1.5 | 3 | 5 | 8 | 11 | 61 | 115 | 145 | 175 | 215 | 288 |
|---|
Power Supply Facility
Capacity (kVA)
∗9 | Without DC Reactor | SLD | 2 | 3.4 | 5 | 7.5 | 12 | 44 | 84 | 103 | - | - | - |
|---|
| LD | 1.9 | 3.2 | 4.7 | 7 | 11 | 41 | 79 | 97 | - | - | - |
|---|
| ND (Initial Setting) | 1.5 | 2.4 | 4 | 5.4 | 8.6 | 37 | 69 | 82 | 101 | - | - |
|---|
| HD | 0.9 | 1.5 | 2.4 | 4 | 5.4 | 30 | 57 | 69 | 82 | - | - |
|---|
| With DC Reactor | SLD | 1.8 | 2.9 | 4 | 6.4 | 10 | 35 | 71 | 89 | 120 | 145 | 181 |
|---|
| LD | 1.6 | 2.7 | 3.7 | 5.8 | 8.8 | 32 | 65 | 81 | 110 | 132 | 165 |
|---|
| ND (Initial Setting) | 1.1 | 1.9 | 3 | 4.2 | 6.7 | 29 | 55 | 67 | 82 | 110 | 132 |
|---|
| HD | 0.6 | 1.1 | 1.9 | 3 | 4.2 | 23 | 44 | 55 | 67 | 82 | 110 |
|---|
| Protective Structure (IEC 60529) ∗10 | Closed Type (IP20) | Open Type (IP00) |
|---|
| Cooling Method | Self-cooling | Forced air cooling |
|---|
| Approx. Weight (kg) | 2.0 | 2.2 | 3.3 | 3.3 | 3.3 | 15 | 42 | 42 | 54 | 74 | 74 |
|---|
∗1 The maximum applicable capacity assumes that Mitsubishi
Electric’s standard 4-pole motor is used.
∗2 With the 0.2 kW motor, only the V/F control can be applied.
∗3 The rated output capacity assumes an output voltage of 220 V.
∗4 The percent value of the rated overload current displays the
ratio for the rated output current of the inverter.
With repeated use, you must wait until the inverter and motor
return to a temperature at 100% load or a lower temperature between
use.
∗5 The maximum output voltage never exceeds the power supply
voltage. The maximum output voltage can be changed within its range
of settings.
However, the wave crest value of the inverter output voltage
waveform is roughly √2 times that of the power supply voltage.
∗6 With a built-in brake resistor
∗7 Value based on the ND rating.
∗8 The rated input current is the value at the rated output
current. The rated input current varies depending on the value of
power supply impedance (including the impedance of the input
reactor and wires).
∗9 The value of power supply capacity is the value at the rated
output current. It varies depending on the value of power supply
impedance (including the impedance of the input reactor and wires).
∗10 FR-DU08: IP40 (excluding the PU connector)
Rated (Standard Structure Models) 400 V Class
∗1 The maximum applicable capacity assumes that Mitsubishi
Electric’s standard 4-pole motor is used.
∗2 With the 0.2 kW motor, only the V/F control can be applied.
∗3 The rated output capacity assumes an output voltage of 440 V.
∗4 The percent value of the rated overload current displays the
ratio for the rated output current of the inverter.
With repeated use, you must wait until the inverter and motor
return to a temperature at 100% load or a lower temperature between
use.
∗5 The maximum output voltage never exceeds the power supply
voltage. The maximum output voltage can be changed within its range
of settings.
However, the wave crest value of the inverter output voltage
waveform is roughly √2 times that of the power supply voltage.
∗6 With a built-in brake resistor
∗7 Value based on the ND rating.
∗8 The rated input current is the value at the rated output
current. The rated input current varies depending on the value of
power supply impedance (including the impedance of the input
reactor and wires).
∗9 The value of power supply capacity is the value at the rated
output current. It varies depending on the value of power supply
impedance (including the impedance of the input reactor and wires).
∗10 FR-DU08: IP40 (excluding the PU connector)
∗11 If 480 V is exceeded, the Pr. 977, "Input Voltage Mode
Selection," must be set.
∗12 The regenerative brake capacity can be improved using a
commercially available brake resistor. For further details, please
contact the Mitsubishi Sales Office.
Applications:
Effective Vector Control Option Required
The displayed protection functions can vary depending on the
option(s) installed. To ensure proper function, the option to
support vector control must be installed.
PM Sensorless Vector Control
If you have selected PM sensorless vector control, please refer to
page 211 for additional information.
Torque Limitation Level
Please note that for models 3 FR-A820-5.5 K (00340) or larger and
FR-A840-5.5 K (00170) or larger, the default value is limited to
150% due to torque limitations.
Standard Structure and IP55 Compatible Models
Protection functions are effective only on standard structure
models and IP55 compatible models. Please refer to the product
specifications to determine compatibility.
Protection Function Limitations
Please be aware that certain protection functions may not work from
the initial state or may only work on specific models. For example,
function 6 works only on standard structure models, while function
7 works only on IP55 compatible models.
Temperature Limitations
While it may be safe to expose the unit to temperatures outside of
the specified range for short periods, such as during shipping,
please adhere to the specified limits when in use.
Altitude Limitations
If installing the unit at an altitude exceeding 1,000 m (up to
2,500 m), please note that the rated current must be reduced by 3%
every 500 m.
Vibration Limitations
Please note that vibrations greater than 2.9 m/s2 are not
recommended for FR-A840-160 K (04320) or larger models.
FR-A800-E Function Limitations
Function 11 works only on the FR-A800-E model.
Packing and Shipping:
Product Packaging:
The Variable Frequency Inverter product will be securely packaged
to ensure that it arrives in pristine condition. The product will
be placed in a sturdy cardboard box with sufficient padding to
prevent any damage during transit.
Shipping:
Once your order has been processed, the Variable Frequency Inverter
product will be shipped to your desired location using a reliable
shipping service. The shipping cost will be calculated based on the
weight and destination of the package. You will be provided with a
tracking number so you can monitor the progress of your shipment.
